Peugeot 106 (phase 2) Gti TU engine (65mm Torque Bush) Vibra Technics Full Race Kit. Further down the listing is a diagram to show the fitment location for the contents of the kit on the car to assist you. The following product is suitable for the: Peugeot 106 (phase 2) Gti TU engine (65mm Torque Bush). This Kit is for Race Use, please check our listings for a Road mount kit. The position of all mountings is described as it would be from the drivers seat. For example, Left Hand mounts are on the Gearbox / passenger side of a Right Hand Drive car. The Kit contains the following items: – Transmission Mount PSA312MX. This is a direct replacement for the original part and will significantly reduce movement at the gearbox end of the power unit in all directions. Helping to reduce tramp under hard accelaration. RH Engine Mount PSA302MX. This is a direct replacement for the original hydraulic mount. Engine movement is significantly reduced in all directions, and the weak 8mm bolt in the original is replaced with a 12mm bolt. The engine bracket will need to be drilled out to 12mm. Instructions are included with the mount. Engine Rear Torque Bush 65mm PSA320B. (Quantity 1) OEM Part Number(s): 1844.54. This is a direct replacement bush for the Saxo (also fits AX and 106). It is significantly stiffer than the original and therefore reduces engine movement under torque. This helps with traction, gearchanging and reduces stress on other components such as exhaust manifold, intake pipes and driveshafts. It is suitable for road and race applications. The bush is a press-fit into the original housing. Please check the diameter of your original bush. It should be 65mm. To be sure of the correct fitment, please use the further specification data above to assist you. The location of some, if not all the Mounts in this kit may be found in the diagram(s) below. Vibra-Technics Mounts are a completely re-engineered Solution. Vibratechnics Uprated Engine Mounts. Vibra-Technics products are designed specifically for high performance applications where a direct replacement for the standard mount is required along with a much higher level of engine control to cope with higher engine outputs and higher road inputs caused by fast driving. The competition mounts can also eliminate clearance problems with strut braces, exhaust systems, body panels etc. Competition mounts are not recommended for road use. Vibra-Technics Uprated Suspension Bushes. Vibra-Technics have developed a small range of suspension bushes which are designed to significantly reduce the suspension geometry changes resulting from acceleration, braking and cornering forces. This gives improvements in the car stability and cornering “feel” without limiting normal suspension travel. C&R sell an extensive range of replacement and High Performance parts for your VW, Audi, Seat and Skoda. Stocking only the Highest Quality brands such as: K&N, Black Diamond, Goodridge, Piper, Kent, Jetex, Superpro, Powerflex, Prothane, Vibra Technics, Redline, Eibach, Koni and Weitec. We’re not just “box movers” we are able to offer in depth technical advise relating to the product or we can provide a fitting service on most of the VAG Group parts we sell in our Nottingham workshop. C & R Enterprises The Volkswagen, Audi, Seat and Skoda Specialists. The item “Peugeot 106 Phase 2 Gti TU engine 65mm Torque Bush Vibra Technics Full Race Kit” is in sale since Sunday, November 20, 2016. This item is in the category “Vehicle Parts & Accessories\Car Parts\Engines & Engine Parts\Engine Mounts”. The seller is “jsm_performance_car_parts” and is located in Nottingham. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia, New Zealand, Egypt, Reunion, South africa.
- Manufacturer Part Number: VTKit100
- Brand: Vibra Technics
- Model: 106 (phase 2) Gti
- Make: Peugeot